PUBLISHER: Mordor Intelligence | PRODUCT CODE: 2163332
PUBLISHER: Mordor Intelligence | PRODUCT CODE: 2163332
According to Mordor Intelligence, the advanced packaging inspection systems market size was USD 3.34 billion in 2025, and USD 3.67 billion in 2026, and is projected to reach USD 6.22 billion by 2031, growing at a CAGR of 11.13% during 2026-2031.

AI accelerator packages are among the most difficult devices to inspect because they combine several dies, dense interconnect structures, and materials with different process histories. Every packaging wafer requires checks of incoming substrate quality, copper redistribution layer patterning, micro-bump coplanarity, die placement, and final package integrity before it can support a high-value system. KLA stated that advanced packaging revenue in its semiconductor process control portfolio was expected to rise from USD 635 million in 2025 to USD 1 billion in 2026. This company result links process-control spending to added packaging capacity and to the larger number of measurement steps used on heterogeneous packages. The advanced packaging inspection systems market benefits when capacity additions require inspection at multiple manufacturing stages rather than relying on a final check alone. Tool demand in the advanced packaging inspection systems market also becomes less dependent on chip volumes because costly multi-die packages require greater inspection coverage for each finished unit.
Hybrid bonding requires inspection methods that can address very small features, buried interfaces, surface conditions, and production throughput at the same time. An ASM Electronic Device Failure Analysis Society study found that no single method provides nanoscale resolution, full-field coverage, subsurface visibility, and manufacturing-compatible throughput across all hybrid-bonding stages. Manufacturers in the advanced packaging inspection systems market, therefore, use optical, infrared, acoustic, and X-ray approaches at distinct points in the bonding flow, rather than treating hybrid-bond inspection as one tool purchase. Onto Innovation described in-line hybrid-bonding tools that combine 3D metrology for particle-height measurement with infrared inspection that can identify voids in dielectric layers. Nova announced in July 2026 that a leading global foundry had selected its WMC platform as its tool of record for advanced packaging measurements following a competitive evaluation. This shift expands the advanced packaging inspection systems market because hybrid bonding transforms a single inspection point into a broader process-control sequence with multiple physical measurement requirements.
Advanced packaging inspection systems require significant capital outlay when a production line uses several inspection technologies, and the equipment must also be integrated with cleanroom operations and maintenance practices. A hybrid-bonding line may need optical, infrared, acoustic, and X-ray tools, with each system serving a different physical measurement requirement. That cost burden is especially difficult for outsourced semiconductor assembly and test providers with narrower equipment budgets and less room to fund full inline coverage. Onto Innovation launched Dragonfly G5 in March 2026 with an optics and illumination design intended to support several HBM4-related applications on one platform. The platform's design reflects customer demand for broader capability without adding a separate tool for every application, while preserving the sensitivity needed for advanced package workflows. Smaller participants in the advanced packaging inspection systems market may continue to use sampling where comprehensive inline inspection is difficult to fund, even though sampling can leave more yield risk in complex multi-die products.
Other drivers and restraints analyzed in the detailed report include:
For complete list of drivers and restraints, kindly check the Table Of Contents.
Optical-based inspection and metrology systems held 42.51% of the advanced packaging inspection systems market share in 2025. Their leading position reflects high throughput, broad use across wafer-level and post-assembly flows, and an established installed base at wafer fabs and outsourced assembly sites. These systems support redistribution layer critical-dimension measurement, bump coplanarity checks, die-shift detection, and macro-defect screening across several package types. Their use in fan-out and flip-chip production aligns with the need to manage inspection speed and cost in high-volume flows. Onto Innovation launched Dragonfly G5 in March 2026 with stated 150 nm defect sensitivity and multi-mode illumination for advanced packaging applications.
Infrared and thermal systems find subsurface voids and delamination in stacked-die structures, while acoustic systems identify underfill and encapsulant issues beyond the reach of surface optical methods. Electron-beam inspection provides electrical-contrast imaging for through-silicon vias and back-end interconnects, and an SPIE paper reported defective-die capture rates up to 4.3 times higher through AI-guided computational sampling. X-ray and computed tomography inspection systems are projected to grow at a 14.80% CAGR through 2031, the highest rate in this segmentation. Research in Microelectronics Reliability showed that high-resolution nano-CT detected sub-micron voids and cracks in 20 µm micro-bumps during a 30-second overview scan. This capability supports inspection of buried joints, HBM continuity, and hybrid-bond interfaces that optical systems cannot directly assess.
Post-assembly inspection held 34.26% of the share in the advanced packaging inspection systems sector in 2025. Its position reflects the installed base of automated optical inspection and 3D inspection systems used after dicing and during package assembly. These tools assess package appearance, solder-related features, alignment, and other visible conditions before shipment. The category remains necessary for every package, including devices made through mature packaging methods. It also serves outsourced assembly operations that process high volumes across multiple customer programs.
Wafer-level inspection in the advanced packaging inspection systems market is projected to expand at a 14.29% CAGR through 2031 because defects found before die attach can prevent loss in a completed multi-die package. A December 2025 review in the Journal of Manufacturing Science and Engineering found that through-silicon vias, hybrid bonding interfaces, and micro-bump arrays are raising requirements for surface and subsurface inspection. Nova released the WMC in August 2025 as a modular optical metrology platform for 2.5D and 3D integration, hybrid bonding, and different wafer sizes. Die-level inspection prevents known-defective dies from entering multi-die assemblies, while final inspection and failure analysis feed findings back to upstream process teams. Cohu stated that its Neon platform was being qualified at a Taiwan-based outsourced assembly site for HBM3, HBM4, and HBM4E applications in 2026.
Asia-Pacific held 59.81% of the share in the advanced packaging inspection systems sector in 2025. Its position follows the region's concentration of advanced packaging capacity, memory production, and outsourced semiconductor assembly operations. Taiwan accounted for nearly 50% of global IC packaging and testing output in 2024, based on ITRI data reported by the Taipei Times, and South Korea adds major HBM packaging activity. Japan contributes precision optics, electron-beam suppliers, outsourced assembly operations, and memory packaging capacity. These production centers make the region important for new equipment installations and field service.
China has a large legacy packaging base within the advanced packaging inspection systems market and an increasing interest in domestically sourced inspection equipment. Camtek reported that China represented 45% of its 2026 revenue. Malaysia, Vietnam, and Singapore are gaining relevance as outsourced assembly capacity expands beyond Taiwan. Their capacity can absorb part of the demand when lead times at established facilities lengthen.
North America in the advanced packaging inspection systems market is projected to grow at a 14.50% CAGR through 2031, making it the fastest-growing geography. SK Hynix held a groundbreaking ceremony in August 2026 for an HBM packaging facility in Indiana that was expected to be a North American HBM production base by 2030. U.S. public awards support packaging research, pilot capacity, substrate development, and materials work. Canada supports packaging research, and Mexico has a role in back-end assembly and test. Europe has a more modest position, led by German and Dutch suppliers serving X-ray, X-ray fluorescence, and atomic-force-metrology applications. South America and the Middle East and Africa remain smaller markets where demand follows contract assembly and test investment.